Opens in a new tab

Reset a Garbage Disposal and Clear a Jam

Bring a stalled, humming, or dead disposal back to life with a safe reset and quick unjam—no plumber needed.
Difficulty: Easy
Success Rate: 90%
Cost: $0 - $10
Estimated Timeline: 10–20m
Turn Off Water: No
Find a Local Plumber
Tools Needed:
  • 1/4″ hex (Allen) wrench for disposal flywheel socket

  • Long tongs or needle-nose pliers

  • Wooden spoon handle (for gentle leverage)

  • Flashlight

  • Small bowl and towel

Materials / Parts:
  • Mild dish soap (for cleanup)

  • Citrus peels or baking soda (odor refresh, optional)

Safety Warnings:
  • Always cut power before touching the disposal: unplug it or switch off the breaker.

  • Never put your hand inside the disposal while power is connected.

  • Use tongs or pliers to remove objects—blades are sharp.

Test & Verify:
  • Disposal starts immediately without humming or tripping.

  • Water and grind chamber clear quickly with normal sound.

  • No leaks under the sink at the disposal body or connections.

Cleanup & Disposal:
  • Wipe the sink flange and splash guard.

  • Deodorize with a few ice cubes and a slice of citrus while running cold water.

  • Dry the cabinet area and store tools.

Pre-Checks:
  • Listen for symptoms: hums (jam), clicks off (overload tripped), or dead (no power).

  • Find the red reset (overload) button on the bottom of the unit.

  • Confirm you have the correct hex wrench for the flywheel socket under the unit.

  • Clear under-sink space and place a towel for drips.

Step-By-Step Instructions:
  1. Unplug the disposal or switch off the circuit breaker. Turn off the wall switch too.

  2. Shine a flashlight into the drain. If you see a foreign object (utensil, bone, pits), remove it with tongs. Do not put your hand inside.

  3. Insert the 1/4″ hex wrench into the flywheel socket on the bottom center of the disposal.

  4. Rotate the wrench back and forth several times to free the jam. You should feel the flywheel loosen.

  5. Press the red reset button on the bottom until it clicks (if it had tripped).

  6. Remove the wrench. Restore power by plugging in or turning on the breaker.

  7. Run cold water. Briefly toggle the disposal switch on for 1–2 seconds, then off. Repeat short pulses until it spins freely.

  8. Let the unit run for 10–15 seconds with cold water to flush remaining debris.

  9. If vibration or noise persists, power off again, re-check for objects with tongs, and repeat the back-and-forth freeing.

When to Stop & Call a Pro:
  • Reset trips again or unit only hums after multiple free-ups.

  • Disposal leaks from the housing (internal seal failure).

  • Electrical issues: breaker trips, cord/plug damage, or burning smell.

  • Flywheel won’t turn with a wrench (seized bearings or foreign object lodged hard).

Common Mistakes:
  • Reaching in with bare hands while the unit has power.

  • Holding the switch on while jammed—can overheat and trip the overload.

  • Using hot water during grinding (grease can liquefy and re-solidify downstream).

  • Forgetting to press the reset after clearing the jam.

Troubleshooting:

Q: Unit is completely dead—no hum, no sound.
A: Press the red reset button; check outlet power and the breaker; confirm wall switch works.

Q: Hums but won’t spin even after wrenching.
A: Jam may persist; remove objects with tongs and repeat back-and-forth turns. If still stuck, motor may be failing.

Q: Spins but water backs up.
A: The P-trap may be clogged; clear the trap or use a small auger.

Q: New unit installed and it only buzzes.
A: Knockout plug in the dishwasher inlet may still be in place; remove per manual (power off first).